Order on weekdays before 2 PM for same-day-shipment

Enter your searchword here...

Searching...

Oh no, we have 0 products that match your search.

  1. Home
  2. Here is How To Cut Magnetic Sheets - Nifty Little Online Guide

Here is How To Cut Magnetic Sheets - Nifty Little Online Guide

When I read the materials list for a DIY project I was planning to do earlier this week, I noticed that a magnetic sheet was included. Since this was a material that I had never worked with before, I started to wonder how I would be able to alter it. So, I did some research to come up with an online guide on how to cut magnetic sheets.

How do you cut magnetic sheets? There are a variety of methods that you can use to go about cutting through a magnetic sheet. Depending on the strength of the material that you will be using, you can cut through it with a paper cutter, a printer and cutting machine, or a regular blade if the thickness will allow it.

Magnetic sheets are very versatile materials that can be used for anything from small refrigerator magnets to large commercial signage. If you are planning on using magnetic sheets for one reason or another in the future, this nifty little online guide should give you all of the information you need to cut through them.

How To Cut Magnetic Sheets

When it comes to cutting through magnetic sheets, it can seem rather difficult due to the strength and durability of the magnet material. While magnetic sheets come in many different sizes and thickness levels, you might find yourself in a situation where you need to cut through a pretty tough sheet.

Today, we will be going over all of the different ways that you could possibly cut magnetic sheets. Later on, in the next sections, each of these methods will be described in more detail, with step by step instructions on how to execute them correctly.

Ways To Cut Magnetic Sheets:

  • Use a Paper Cutter
  • Use a Blade
  • Use a Printer/Cutting Machine

The three most common methods of cutting through magnetic sheets include the use of a paper cutter or a printer and cutting machine. Alternatively, you can go with the classic method of using a very sharp blade if the thickness of the magnetic sheet permits.

How To Cut a Magnetic Sheet With a Blade

Perhaps the most obvious method for cutting through a magnetic sheet, or any other kind of material for that matter, would be to use a sharp blade or utility knife.

Depending on how thick and strong the magnetic sheet is, you might be able to use the blade alone to quickly slice through it and produce a clean cut.

How To Cut a Magnetic Sheet With a Blade:

  1. Place the magnet on a clean flat surface (magnet side down)
  2. Use a ruler or straight edge to define the cutting line
  3. Use your non-dominant hand to hold the magnet and straight edge in place
  4. Use your dominant hand to run the blade across the line on the opposite side (away from hand and body)
  5. Fold the magnet to break it apart along the line you created, repeat as needed

The process of cutting a magnetic sheet with a utility knife is almost as easy as it sounds, as long as you follow through with the proper safety precautions in doing so.

First, you will want to place the magnet on a clean and flat surface with the magnet side facing down. Use a ruler or a straight edge to define the line that you would like to cut directly next to it on the sheet.

Next, use your non-dominant hand to hold the magnet and the straight edge in place at the same time, placing your palm firmly down on the sheet and the tip of your index finger on the very edge of the ruler.

Proceed by using your dominant hand to run the blade across the line on the opposite side of your hand, moving it away from yourself. Fold the magnet to break it apart along the line you created, and repeat these steps as necessary.

How To Cut a Magnetic Sheet With a Paper Cutter

When it comes to cutting through a magnetic sheet, the use of a durable heavy duty paper cutter will definitely do the trick. If you have access to one at home or you are able to use one at another location for this purpose, you will be able to quickly and easily complete this task.

Take a look at the steps below that you can follow with only your magnet sheet and paper cutter. Make sure to pay attention to all of the safety precautions that are mentioned in this outline as well.

How To Cut a Magnetic Sheet With a Paper Cutter:

  1. Obtain a heavy-duty paper cutter and place it on a flat surface
  2. Place the magnet sheet onto the paper cutter (magnet face down)
  3. Carefully place the magnet along the steel edge
  4. Use your left hand to hold the magnet in place (fingers away from the blade)
  5. Use your right hand to push the blade down toward the magnet
  6. Remove your magnet sheet and return the blade to its downward position

Once you have obtained your heavy duty paper cutter and placed it onto a flat surface, you will begin by placing the magnet sheet onto the paper cutter. In doing this, the magnet side of the sheet should be face down.

Next, you will need to carefully push the magnet into place until the edge of where you would like to cut is lined up with the steel trim on the end of the machine that is closest to the blade. At this point, the blade will be elevated to allow this movement.

Use your left hand to hold the magnet in place with your fingers as far away from the blade as possible. Then, use your right hand to grab the handle of the blade and push it down toward the magnet, quickly and precisely cutting along the guideline you set.

Remove your magnet sheet and return the blade to its downward position along the edge of the board once you are satisfied with the cut you have made.

How To Cut a Magnetic Sheet With a Printer/Cutting Machine

Another great way to cut through a magnetic sheet is to use a printer and cutting machine combination if you are able to get your hands on one.

Among one of the easiest and fastest methods for those who know how to use them, you will be able to alter your magnetic sheet in no time with one of these machines.

How To Cut a Magnetic Sheet With a Printer/Cutting Machine:

  1. Place the magnetic sheet onto a cutting mat (magnet side down)
  2. Load the cutting mat into the machine from the bottom (magnet side down)
  3. Indicate the correct material option on your computer
  4. Wait for the magnet to return from the machine and pull it apart

This method will be as simple as placing your magnetic sheet face down onto a special cutting mat that is fitted to the printer and cutting machine that you are using. If you are trying to cut out a design or specific shape very precisely, this might be the best technique for you.

Proceed by loading the mat into the machine from the bottom, indicating the correct material option of the computer, and waiting for the magnet to return from the machine. Finally, you will pull off the excess material that was cut by the machine and take home your design.

As you can see, there are plenty of methods in which you can cut into a magnetic sheet. Regardless of the tools and materials that you have access to, you will be able to come out with a great result following the techniques that were discussed in this article.

Related Questions

How can stronger and thicker magnets be cut?

To cut into a stronger and thicker magnet, you can use a hacksaw, drill, chisel, or something similar. However, these types of magnets are likely to break.

What kind of projects can magnetic sheets be used for?

They can be used to hang photographs, business signage, and can even be fashioned into holders for fabric curtains.

Related products - Here is How To Cut Magnetic Sheets - Nifty Little Online Guide